Commit c2a7bb52 authored by Dmytro Oz's avatar Dmytro Oz Committed by Adrian Schmutzler
Browse files

ramips: mt7621: add support for Xiaomi Mi Router 4

Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).

Specifications:

Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A

UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:c2      factory 0xe000 (label)
WAN   *:c3      factory 0xe006
2g    *:c4      factory 0x0000
5g    *:c5      factory 0x8000

Flashing instructions:

1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:

setenv uart_en 1
saveenv
boot

3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/

Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion

Signed-off-by: default avatarDmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
parent 93be5926
......@@ -48,6 +48,7 @@ linksys,ea7300-v2|\
linksys,ea7500-v2|\
xiaomi,mi-router-3g|\
xiaomi,mi-router-3-pro|\
xiaomi,mi-router-4|\
xiaomi,mi-router-ac2100|\
xiaomi,redmi-router-ac2100)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x20000"
......
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621_xiaomi_nand_128m.dtsi"
/ {
compatible = "xiaomi,mi-router-4", "mediatek,mt7621-soc";
model = "Xiaomi Mi Router 4";
aliases {
led-boot = &led_status_yellow;
led-failsafe = &led_status_red;
led-running = &led_status_blue;
led-upgrade = &led_status_yellow;
label-mac-device = &gmac0;
};
leds {
compatible = "gpio-leds";
led_status_red: status_red {
label = "red:status";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
led_status_blue: status_blue {
label = "blue:status";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
led_status_yellow: status_yellow {
label = "yellow:status";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
};
};
&keys {
minet {
label = "minet";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "pci14c3,7603";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0000>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "pci14c3,7662";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&gmac0 {
mtd-mac-address = <&factory 0xe000>;
};
&switch0 {
ports {
port@1 {
status = "okay";
label = "lan1";
};
port@2 {
status = "okay";
label = "lan2";
};
port@4 {
status = "okay";
label = "wan";
mtd-mac-address = <&factory 0xe006>;
};
};
};
&state_default {
gpio {
groups = "jtag", "uart2", "uart3", "wdt";
function = "gpio";
};
};
......@@ -1277,6 +1277,14 @@ define Device/xiaomi_mi-router-3-pro
endef
TARGET_DEVICES += xiaomi_mi-router-3-pro
define Device/xiaomi_mi-router-4
$(Device/xiaomi_nand_separate)
DEVICE_MODEL := Mi Router 4
IMAGE_SIZE := 124416k
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
endef
TARGET_DEVICES += xiaomi_mi-router-4
define Device/xiaomi_mi-router-4a-gigabit
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
......
......@@ -19,6 +19,7 @@ ramips_setup_interfaces()
mikrotik,routerboard-m33g|\
xiaomi,mi-router-3g|\
xiaomi,mi-router-3g-v2|\
xiaomi,mi-router-4|\
xiaomi,mi-router-4a-gigabit)
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
;;
......
......@@ -63,6 +63,7 @@ platform_do_upgrade() {
netis,wf2881|\
xiaomi,mi-router-3g|\
xiaomi,mi-router-3-pro|\
xiaomi,mi-router-4|\
xiaomi,mi-router-ac2100|\
xiaomi,redmi-router-ac2100)
nand_do_upgrade "$1"
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment